Canon CanoScan 4200F
USB
0x04a9
0x221b
Here are the numbers of the four major chips on the board.
chip 1
ESMT
M12L16161A- 7T
LNS1P43ZE 0503
This is the DRAM module used inside this scanner
chip 2
610800017919 D1
0521 TH07
XHHL7G0000GG
This is a remarked ALI M5623D scanner controller. There is a
product brief describing its features.
chip 3
WM
WM8196SCDS
55AMPBX
This scanner uses a Wolfson Electronics WM8196SCDS chip as ADC.
There is also a datasheet available:
chip 4
ST E
L6219DS
9913M V6
MYS 99 507
This is the controller of the scanner motor
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=04a9 ProdID=221b Rev= 2.00
S: Manufacturer=Canon
S: Product=CanoScan
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 10mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=16ms
<device descriptor of 0x04a9/0x221b at 001:003 (Canon CanoScan)>
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255
bDeviceSubClass 255
bDeviceProtocol 255
bMaxPacketSize0 64
idVendor 0x04A9
idProduct 0x221B
bcdDevice 2.00
iManufacturer 3 (Canon)
iProduct 4 (CanoScan)
iSerialNumber 0 ()
bNumConfigurations 1
<configuration 0>
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0 ()
bmAttributes 192 (Self-powered)
MaxPower 10 mA
<interface 0>
<altsetting 0>
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255
bInterfaceSubClass 255
bInterfaceProtocol 255
iInterface 0 ()
<endpoint 0>
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 (in 0x01)
bmAttributes 2 (bulk)
wMaxPacketSize 512
bInterval 0 ms
bRefresh 0
bSynchAddress 0
<endpoint 1>
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 (out 0x02)
bmAttributes 2 (bulk)
wMaxPacketSize 512
bInterval 0 ms
bRefresh 0
bSynchAddress 0
<endpoint 2>
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 (in 0x03)
bmAttributes 3 (interrupt)
wMaxPacketSize 1
bInterval 8 ms
bRefresh 0
bSynchAddress 0
<trying to find out which USB chip is used>
checking for GT-6801 ...
this is not a GT-6801 (bcdUSB = 0x200)
checking for GT-6816 ...
this is not a GT-6816 (bDeviceClass = 255, bInterfaceClass = 255)
checking for GT-8911 ...
this is not a GT-8911 (check 1, bDeviceClass = 255, bInterfaceClass = 255)
checking for MA-1017 ...
this is not a MA-1017 (bDeviceClass = 255, bInterfaceClass = 255)
checking for MA-1015 ...
this is not a MA-1015 (bcdUSB = 0x200)
checking for MA-1509 ...
this is not a MA-1509 (bcdUSB = 0x200)
checking for LM983[1,2,3] ...
this is not a LM983x (bcdUSB = 0x200)
checking for GL646 ...
this is not a GL646 (bDeviceClass = 255, bInterfaceClass = 255)
checking for GL646_HP ...
this is not a GL646_HP (bcdUSB = 0x200)
checking for GL660+GL646 ...
this is not a GL660+GL646 (bDeviceClass = 255, bInterfaceClass = 255)
checking for GL841 ...
this is not a GL841 (writing register failed)
checking for ICM532B ...
this is not a ICM532B (check 2, bcdUSB = 0x200)
checking for PV8630/LM9830 ...
this is not a PV8630/LM9830 (bDeviceClass = 255)
checking for M011 ...
this is not a M011 (bcdUSB = 0x200)
checking for RTS8822L-01H ...
this is not a RTS8822L-01H (bDeviceClass = 255)
checking for rts8858c ...
this is not a rts8858c (bDeviceClass = 255)
checking for SQ113 ...
this is not a SQ113 (bDeviceClass = 255)
<Couldn't determine the type of the USB chip (result from sane-backends 1.0.18)>
found USB scanner (vendor=0x04a9 [Canon], product=0x221b [CanoScan]) at libusb:001:003